OTOY Forums

I was if people have come up with a decent way to do the glow effect of a lightsaber. Something that can be customized depending on the saber color. After all, there are Sabers that have a black interior color with a outer glow color. I was thinking about having it as an interior rod which glows the inner color, with a transparent outer rod with the glow color. This would allow you to have the split, but I worry about the outer glow 'tainting' the inner glow for a white inner. Thoughts?

with separate inner and outer rod the color will only interfere when emission value is high, use 1-3 as power with surface brightness enabled.
To get a smoother transition, you can use a gradient or falloff node in the opacit in the outer rod and a gradient in the emission color.

wimvdb wrote:with separate inner and outer rod the color will only interfere when emission value is high, use 1-3 as power with surface brightness enabled.
To get a smoother transition, you can use a gradient or falloff node in the opacit in the outer rod and a gradient in the emission color.

Okay....this is good advice. Never uses a falloff node, so no idea how to make that work. The gradient seems to work, but not as well as I'd like. Any help would be greatly appreciated, this is something entirely new to me.

The falloff map is a blend node between 2 textures/colors which depends on the viewing angle. The skew factor is where you define how strong the angle effect is. Set up a mix texture, put the falloff map in the Amount and the two colors in the textures.
You can also use the falloff map in the opacity (colors white and black) to fade out the material.

It is also the mode you would use in velvet type materials

wimvdb wrote:The falloff map is a blend node between 2 textures/colors which depends on the viewing angle. The skew factor is where you define how strong the angle effect is. Set up a mix texture, put the falloff map in the Amount and the two colors in the textures.
You can also use the falloff map in the opacity (colors white and black) to fade out the material

Okay,I mostly have this look. I put the falloff in the opacity and got it where it looks good going between the 'inner' color and the 'outer' color. But now am having a hard time making the edge of the outer color less harsh. Give it a softer gradient on the edge. I tried doing it as a subtract where the top value was the solid Edge falloff and it was subtracting a gradient of another edge falloff that was tighter (basically a falloff that just gave the rim of the outer) but it doesn't seem to work. Is there a better way to give the edge a gradient, or maybe give a 'glow" around the edge that will soften the edge?

Nephanor wrote:

wimvdb wrote:The falloff map is a blend node between 2 textures/colors which depends on the viewing angle. The skew factor is where you define how strong the angle effect is. Set up a mix texture, put the falloff map in the Amount and the two colors in the textures.
You can also use the falloff map in the opacity (colors white and black) to fade out the material

Okay,I mostly have this look. I put the falloff in the opacity and got it where it looks good going between the 'inner' color and the 'outer' color. But now am having a hard time making the edge of the outer color less harsh. Give it a softer gradient on the edge. I tried doing it as a subtract where the top value was the solid Edge falloff and it was subtracting a gradient of another edge falloff that was tighter (basically a falloff that just gave the rim of the outer) but it doesn't seem to work. Is there a better way to give the edge a gradient, or maybe give a 'glow" around the edge that will soften the edge?

You can have more control over the falloff by using multiple stop points in the gradient node. Unfortunately, the plugin does not support that directly, but indirectly you can by using the edit button in the material properties. When you do this, you can enter all octane material nodes and edit them within octane. The gradient with a single begin and end point is a smooth transition. By adding stop points you can make the transition behave differently: Add a node closer to begin or end point and it will be more like a exponential fall off. You can add as many stop points as you need.
Alternatively you use the octane standalone to create the material, save it as a orbx in localdb and apply it in the plugin.