Page 1 of 1
WAIT WHAT?
Posted: Sun Aug 11, 2019 4:28 pm
by LightwaveGuru
wait what? its new in lw 2019.1.2. (in lw 2019.1 this pop up is not shown). so whats happen there?
i use the Octane V 4.04 plug in
snip lwguru
Re: WAIT WHAT?
Posted: Mon Aug 12, 2019 8:06 am
by juanjgon
This sounds like an installation problem to me, or a problem while trying to load an Octane 2018/2019 scene on Octane 4.04. In the first case, you should try to fully clean your LW config files and add the plugin again.
Thanks,
-Juanjo
Re: WAIT WHAT?
Posted: Mon Aug 12, 2019 1:32 pm
by LightwaveGuru
juanjgon wrote:This sounds like an installation problem to me, or a problem while trying to load an Octane 2018/2019 scene on Octane 4.04. In the first case, you should try to fully clean your LW config files and add the plugin again.
Thanks,
-Juanjo
the scene was build with lw 2019.1 with the same octane plug in. if you load the scene in lw 2019.1.2 this message plop up. so i think its a LW Problem, not a Octane Problem.
anyway...deinstall 2019.1.2 LOL
p.s. so lw 2019.1.2 and the octane plug in was a fresh installation. if you ignore this message octane works. so the plug in is correct installed.
Re: WAIT WHAT?
Posted: Mon Aug 12, 2019 1:35 pm
by Lewis
Hi Rene, can you confirm that for sure and then report to NewTek if it's indeed LW 2019.1.2 issue vs LW 2019.1 ?
What about LW 2019.1.1 ?
Re: WAIT WHAT?
Posted: Mon Aug 12, 2019 1:41 pm
by LightwaveGuru
Lewis wrote:Hi Rene, can you confirm that for sure and then report to NewTek if it's indeed LW 2019.1.2 issue vs LW 2019.1 ?
What about LW 2019.1.1 ?
its reported to DEUCE via FB. no answere in the moment. i think the bug fixes from open VDB (in lw 2019.1.2) is the reason for that. (my guess)
snip lwguru
Re: WAIT WHAT?
Posted: Mon Aug 12, 2019 1:43 pm
by LightwaveGuru
Lewis wrote:Hi Rene, can you confirm that for sure and then report to NewTek if it's indeed LW 2019.1.2 issue vs LW 2019.1 ?
What about LW 2019.1.1 ?
p.s.
also all my level sets from open VDB react different in lw 2019.1.2 (total other simulations if i start it) ...so i de:install it and work with lw 2019.1
snip lwguru
Re: WAIT WHAT?
Posted: Mon Aug 12, 2019 1:49 pm
by LightwaveGuru
Lewis wrote:Hi Rene, can you confirm that for sure and then report to NewTek if it's indeed LW 2019.1.2 issue vs LW 2019.1 ?
What about LW 2019.1.1 ?
i think that here is the reason...(my guess)
lw 2019.1.2 >
LWB-5310 advection saving fix.
LWB-5311 velocity problem. Revise grid math.
LWB-5313 trail length. fix trail length when using nodal particle system.
Thats all Open VDB related.
snip lwguru