Remaining sparklies

Forums: Remaining sparklies
Discuss or ask critique about your current works
Forum rules
Important notice: All artwork submitted on our public gallery forums gallery forums may or may not be used by OTOY for publication on our website gallery.
If you do not want us to publish your art, please mention it in your post clearly. (put a very red small diagonal cross in the left right corner of the image)
Any images already published on the gallery will be removed if the original author asks us to do so.
We recommend placing your credits on the images so you benefit from the exposure too, and use a minimum image width of 1200 pixels, and use pathtracing or PMC. Thanks for your attention, The OctaneRender Team.


For new users: this forum is moderated. Your first post will appear only after it has been reviewed by a moderator, so it will not show up immediately.

This is necessary to avoid this forum being flooded by spam.

Remaining sparklies

Postby moose69 » Wed Oct 25, 2017 2:37 pm

moose69 Wed Oct 25, 2017 2:37 pm
Hi All

Please see attached an image I have produced. I cannot seem to get rid of the last sparklies in the top of the 3 bottles. I have set Path tracing up as I see best from the manual but these settings no matter how high the Max samples remove them.

As I understand I have Upped caustic blur, reduced GI clamp and allowed adaptive sampling to do it's thing but to no avail. Any thoughts would be appreciated.

System 6 core i7 / 32GB RAM / 2x 1070 + 1x 1080, Octane 3.06 in C4D R18

settings.jpg

settings.jpg


Thanks
Attachments
mer group outside.jpg
moose69
Licensed Customer
Licensed Customer
 
Posts: 37
Joined: Sun Jan 17, 2016 10:10 pm

Re: Remaining sparklies

Postby bepeg4d » Thu Oct 26, 2017 10:54 am

bepeg4d Thu Oct 26, 2017 10:54 am
Hi moose69,
please update to 3.07-R1:
viewtopic.php?f=85&t=63700
About the noise in liquid:
what is your exposure value?
Could post a screenshot off the noise pass in that zone?
Did you tried to add a render region in that zone?
Are you using an HDRI for lighting?
ciao beppe
User avatar
bepeg4d
Octane Guru
Octane Guru
 
Posts: 9940
Joined: Wed Jun 02, 2010 6:02 am
Location: Italy

Re: Remaining sparklies

Postby moose69 » Thu Oct 26, 2017 5:03 pm

moose69 Thu Oct 26, 2017 5:03 pm
Hi

exposure 1.8

yes HDRI

no render region as will be animating over 5 seconds

image attached showing noise

thanks
Attachments
noise.png
moose69
Licensed Customer
Licensed Customer
 
Posts: 37
Joined: Sun Jan 17, 2016 10:10 pm

Re: Remaining sparklies

Postby bepeg4d » Fri Oct 27, 2017 5:14 am

bepeg4d Fri Oct 27, 2017 5:14 am
Hi moose69,
please, always set the expected exposure as the same has the exposer value in the imager.
Sorry, it is possible to see the noise pass at the end of render time?
Are you using RGB Spectrum node in Absorption for coloring the liquid?
ciao beppe
User avatar
bepeg4d
Octane Guru
Octane Guru
 
Posts: 9940
Joined: Wed Jun 02, 2010 6:02 am
Location: Italy

Re: Remaining sparklies

Postby moose69 » Fri Oct 27, 2017 10:15 am

moose69 Fri Oct 27, 2017 10:15 am
Thanks I will do another noise render.

What difference will the expected exposure make?

The liquids are coloured in transmission with roughness and no medium input
moose69
Licensed Customer
Licensed Customer
 
Posts: 37
Joined: Sun Jan 17, 2016 10:10 pm

Re: Remaining sparklies

Postby bepeg4d » Fri Oct 27, 2017 4:04 pm

bepeg4d Fri Oct 27, 2017 4:04 pm
Hi moose69,
about Expected exposure value, it’s a general rule when you use Adaptive sampling, otherwise leave the value at 0:
Expected exposure: The expected exposure should be approximately the same value as the exposure in the imager or 0 to ignore this setting. The default is 0. It's used by adaptive sampling to determine which pixels are bright and which are dark, which obviously depends on the exposure setting in the imaging settings.
If set to something not 0, adaptive sampling tweaks/reduces the noise estimate of very dark areas of the image. It also increases the min. adaptive samples limit for very dark areas which tend to find paths to light sources only very irregularly and thus have a too optimistic noise estimate.


About color in transmission, you can use a Gaussian color node instead of RGB color node, probably you should have less noise inside the liquid.
ciao beppe
User avatar
bepeg4d
Octane Guru
Octane Guru
 
Posts: 9940
Joined: Wed Jun 02, 2010 6:02 am
Location: Italy

Re: Remaining sparklies

Postby moose69 » Fri Oct 27, 2017 9:08 pm

moose69 Fri Oct 27, 2017 9:08 pm
Thanks

I reduced GI clamp, increased caustic blurring, reduced hot pixel value and changed the expected exposure as suggested and obtained a satifactory result.

Thanks for your help :-)
moose69
Licensed Customer
Licensed Customer
 
Posts: 37
Joined: Sun Jan 17, 2016 10:10 pm

Return to Works In Progress


Who is online

Users browsing this forum: No registered users and 10 guests

Thu Mar 28, 2024 3:10 pm [ UTC ]