Page 4 of 21
Re: OctaneRender 3 for ArchiCAD [TEST and STABLE]
Posted:
Fri Oct 21, 2016 3:33 am
by Daniel_Ward
HI Paul,
usually when I get a crash, the whole system just freezes and I have to do a hard reset to get going again. I'm not sure a dump report exists in that situation?
I had a system freeze not long after making the post, ironically. I had 3 copies of AC20 and 2 copies of AC19 running. I was rendering on one of the AC19 projects at the time and watching something on YouTube, which possibly wasn't a great idea.
Cheers, Dan.
Re: OctaneRender 3 for ArchiCAD [TEST and STABLE]
Posted:
Fri Oct 21, 2016 10:07 pm
by face_off
usually when I get a crash, the whole system just freezes and I have to do a hard reset to get going again. I'm not sure a dump report exists in that situation?
A complete system fresh would either be a hardware issue, or you have run out of RAM.
I had a system freeze not long after making the post, ironically. I had 3 copies of AC20 and 2 copies of AC19 running. I was rendering on one of the AC19 projects at the time and watching something on YouTube, which possibly wasn't a great idea.
This would take a lot of system resources, so sounds more like a "running out of RAM" issue to me.
Paul
Re: OctaneRender 3 for ArchiCAD [TEST and STABLE]
Posted:
Sat Oct 22, 2016 11:59 pm
by face_off
I have updated the installers at the top of this thread with:
3.4.1.67
- Compiled with Octane 3.04.1
- Fixed issue where the AO Texture could not be disconnected
Paul
Re: OctaneRender 3 for ArchiCAD [TEST and STABLE]
Posted:
Wed Nov 02, 2016 10:38 pm
by face_off
I have updated the installers at the top of this thread with:
3.4.3.68
- Compiled with Octane 3.04.3
- Resolved issue where loading OCS/ORBX proxies was not working unless there was a Geometry Out node in the proxy being loaded.
Paul
Re: OctaneRender 3 for ArchiCAD [TEST and STABLE]
Posted:
Wed Nov 16, 2016 12:18 am
by face_off
I have updated the installers at the top of this thread with:
3.4.4.68
- Compiled with Octane 3.04.4
Paul
Re: OctaneRender 3 for ArchiCAD [TEST and STABLE]
Posted:
Thu Nov 17, 2016 10:44 am
by face_off
I have updated the AC20 installer link at the top of this thread. It was linked to an older installer, and is now linked to 3.4.4.68.
Paul
Re: OctaneRender 3 for ArchiCAD [TEST and STABLE]
Posted:
Sun Nov 27, 2016 7:38 pm
by Daniel_Ward
Hi Paul,
if you could update the AC Plug-ins to 3.04.5 would be great.
Cheers, Dan.
Re: OctaneRender 3 for ArchiCAD [TEST and STABLE]
Posted:
Mon Nov 28, 2016 1:29 am
by face_off
I have updated the installers at the top of this thread with:
3.4.5.68
- Compiled with Octane 3.04.5
Paul
Re: OctaneRender 3 for ArchiCAD [TEST and STABLE]
Posted:
Sun Dec 04, 2016 4:47 am
by Daniel_Ward
Hi Paul,
do you know if the new rounded edges support in the 3.05 will work with the AC Plugin?
Cheers, Dan.
Re: OctaneRender 3 for ArchiCAD [TEST and STABLE]
Posted:
Sun Dec 04, 2016 10:37 am
by face_off
Hi Dan.
The current Octane round edges functionality requires welded vertices on the edge being rounded - however ArchiCAD generally has unwelded vertices where two surfaces join, the edge rounding will not work.
Paul